Hand & Saw Woodwright
  • Home
  • INFO
    • Process
    • Ordering
    • Contact Us
  • Commissioned
  • Available Now
  • Blog

Camphor Slab

February, 2021 - Milton, FL
Two salvaged Camphor slabs joined together.
​87" x 51"
Click here for the finishing video on Facebook

Picture

Bench

January, 2021 - Milton, FL



Customer Service Podium

July, 2019 - Milton, FL

The main structure of the table is constructed from a single piece of live-edge quilted maple. The bark had to be removed from the live-edge prior to any surface milling. This was done with a chisel and cleaned up with sandpaper. 
Two traditional black cherry bow-ties were inlaid to provide a mechanical clamp against the large crack that protruded from one end.
The main structure of the table was fabricated by cutting apposing 45-degree miters in the maple. Floating tenons were used to aid in alignment and provide additional strength to the joint. The result was a c-shaped structure where the grain and figuring of the wood wraps around the corners.
A cherry colored gel stain was used to tint the maple. This tone was enough to darken the wood without distracting from the grain of the quilted and birds-eye figuring. Five coats of polyurethane were applied over the gel stain. Polyurethane provides a durable finish that will protect the wood from moisture and everyday contact.

War Chest

June, 2019 - Milton, FL

Commissioned going away gift for a respected military leader. This chest was designed to mimic in appearance and construction chests found commonly in the Campaign Furniture genre. It contains several small details that highlight the craftsmanship and quality found in high end furniture. 
 
Construction Details: Handcrafted from a single Mahogany board. Mahogany is a wood traditionally used in campaign furniture because of it’s attractive appearance and stability when exposed to varying moisture and temperatures. The alignment of grains across adjacent surfaces is a small detail that provides balance and  improves the appearance without being obvious. The joinery used is thru dovetails. This provides an attractive edge detail and durable construction. The darker end-grain from the adjacent board is clearly visible. The end grain is darker because it absorbs finish more readily than side grain. 
 
Premium brass hardware was selected for the handles and hinges. The brass handles are inset for an attractive low profile appearance. These handles are polished and unfinished. Over time, they will age to an attractive patina. 
 
The chest was finished with three coats of clear lacquer and three coats of wax. This provides a durable easy to maintain finish.
 
Dimensions: 20” Wide X 12” Deep X 14” Tall
Material: Mahogany​

Custom White Oak Hutch

May, 2019 - Milton, FL
Traditional joinery and simple, clean Mid-Century design.

Custom Built In Desk & Wall Cabinet

July, 2018 - Crestview, FL



Arbor & Side Entrance Gate

August, 2018 - Milton, FL

​One of a kind arbor and side entrance with heavy duty custom gate.
  • Traditional timber frame construction (no metallic fasteners), large hand cut mortise & tenon joinery.
  • Marine grade epoxy commonly used for wooden boat building was used to secure joints and seal the end grain of each piece. 
  • The timber is locally sourced cypress from Wilson Lumber. Cypress is a great lumber for exterior projects as it's rot and bug resistant.
  • ​The timber posts extend 36 inches into the ground into 400lb concrete footers.
  • After consulting with the customer, the Arbor was painted with a commercial grade exterior paint. Application of the paint helps to protect the Arbor from weather and reduce the frequency of periodic maintenance.
  • With the paint applied, the wood is less susceptible to the expanding, contracting, splitting and cracking caused by cycles of being wet or dry and hot or cold.
  • Side fence panels are constructed of treated lumber and faced with Hardie board. Hardie board is siding constructed of concrete and fiberglass fillers. It's a durable exterior layer that is rot and bug resistant. 
  • Quality exterior hardware was used. Handle and screws are powder coated. Self closing hinges are used to ensure the gate remains closed. ​

Multi-Use Shadow Box for retiring US Air Force Veteran

September, 2017 - Niceville, FL

White Oak
Custom fit for client's cedar chest or to be hung
Custom side bead trim made from the same stock as the case
Frame cut from one piece of lumber so that the end grain is continuous on both sides
Finished with gel stain and a wipe on polyurethane

We were asked to build a shadow box for a retiring US Air Force Veteran. His wife had a cedar chest that used to store old uniforms and mementos from his career. The shadow box was sized to fit in the top of the chest or hung on a wall for display.
Single coat of gel stain and two coats of wipe on polyurethane (semi-gloss). The gel stain provides a really even color and highlights the grain and character of the oak.
Navy blue felt installed on an oak backer board with custom installed of USAF rank pins.September, 2017 - Niceville, FL
Multi-Use Shadow Box for retiring US Air Force Veteran
Multi-Use Shadow Box for retiring US Air Force Veteran
This frame is cut from one piece of lumber so that the grain is continuous on both sides
This frame is cut from one piece of lumber so that the grain is continuous on both sides
Glass is installed and trimmed with custom side bead trim made from the same stock as the case. This ensures that the grain and stain of the trim match the case of the display. Single coat of gel stain and two coats of wipe on polyurethane (semi-gloss). The gel stain provides a really even color and highlights the grain and character of the oak.
Navy blue felt installed on an oak backer board with custom installed of USAF rank pins.
Navy blue felt installed on an oak backer board with custom installed of USAF rank pins.

Walnut Live Edge Growth Chart

October, 2017 - Niceville, FL

Walnut
Custom planed to 3/4" thickness
Trim routed numbers, finished with a paring chisel
Hand painted accents with satin black 
2 coats of wipe on semi-gloss polyurethane finish

Close friends asked if we could find a really nice piece of lumber to build a growth chart for their son. We dug through our stash of walnut and found a piece with some unique grain. 

The piece started as a rough cut board approximately 1" thick. It had a pretty good warp and twist on it that needed to be addressed before we could run out through the planer. We knocked the high spurs down with hand planes until one side was flat. After a few passes through the planer, the board was ¾" thick. 
Picture
Custom planed from 1" to 3/4" thickness
Really unique grain on this Walnut: picture taken after final sanding with mineral spirits applied to show the grain.
The numbers were cut with a trim router and finished with a paring chisel.
The numbers were cut with a trim router and finished with a paring chisel.
The numbers and ticks marks were painted with satin black black. The board was finished with two coats of wipe on polyurethane (semi-gloss).

Custom 20 Foot Seating and Storage Unit

July, 2017 - Milton, FL

3/4" Birch Plywood
Premium grade southern yellow pine trim
Mitred panels to hide end-grain
Floating mortise and tenon (eliminates the need for metallic fasteners)

This commission involved designing and fabricating a storage area for gym bags and a seating area.  The result was a 20 foot long birch plywood and pine cabinet with 18 inch cubes for storage.  Client requested the piece be unfinished.

Traditional Japanese Style Arbor

June, 2017 - Milton, FL

Dimensions are: 10 feet tall, 42 inches wide, 500 pounds

6' x 6' Cypress beams sourced from our local cypress mill (Wilson Lumber) 
Mortise and tenon (no metal used)

Traditionally styled and constructed Japanese Arbor ​
Picture

Desk & Half-wall Countertops

June, 2017 - Milton, FL

Dimensions are: 

Military Shadow Box and Display

June, 2017 - Niceville, FL

Dimensions are: 48" long, 12" wide, and 5" tall.
Walnut
Mitered corners
​Custom double side-bead trim
Hidden magnet anchoring
3 coats of wipe on polyurethane for the finish

​We were asked to design a very special military shadow box and display for some unique items. 

Double Arched Entrance Gate

March, 2017 - Niceville, FL

Dimensions: 12 feet wide (Two 6-foot gates)
Pressure treated Southern Yellow Pine
Ship-lap slats
Half lap and pinned joint construction
Sealed with Cabots Gold Ultimate finish in Midnight Mahogany
Zinc plated hardware

​We were asked to design a double gate that would provide privacy and an attractive entrance to the back yard.  We collaborated with the client on several design iterations.  The result was a double arched gate with ship-lap paneling constructed of pressure treated lumber that was sealed to provide years of service. It was mounted with triple steel hinges and spring loaded gate wheels.

Massage Therapy Cabinet

August, 2016 - Milton, FL

​Dimensions: 22-3/4 X 15-3/4 X 34-1/2 inches
Southern yellow pine and birch 
Roman ogee
Bead trim
Mortise & Tenon construction
Half blind dovetailed drawer on a traditional slide
Finished back to allow for flexibility in how it can be used

A local massage therapist asked if we could design and build a cabinet for her room. She provided overall dimensions and listed several details that she would like to see. Our customer was ecstatic with the way it turned out. 

5 Panel Barn Door with Glass inserts

​April, 2016 - Valparaiso, FL

Locally milled cypress
Hammered  texture glass panels
Cove trim detail
Mortise & Tenon construction

Classic 5 panel door - Traditional construction using mortise and tenon joinery. Door was sized to cover existing doorway trim. Primed and painted before delivery and installation.   

Craftsman Style 4 Panel Barn Door

April, 2016 - Valparasio, FL
​
Locally milled cypress
Birch plywood panels
Cove trim detail
Mortise & tenon joinery

Craftsman 4 panel door  - Traditional construction using mortise and tenon joinery. Door was sized to cover existing doorway trim. Primed before delivery and installation. 

Trestle Desk 

​December, 2015 - Navarre, FL

Our client provided basic plans for this desk and gave us some artistic freedoms to improve design and appearance. The desk is constructed of yellow pine lumber that provides for an attractive paint or stain finish (The customer requested the desk unfinished). Changes to the design include:

Mitered edges
Custom wood plugs to hide fasteners 
Dovetail joints create an attractive look and add strength to design
Chamfered edges  around the desktop

Pergola

​July, 2015 - Shalimar, FL

10 ft x 10 ft Custom pergola - Pergola constructed from locally milled cypress lumber. Design incorporates unique features such as a custom end profile and lap joint construction. Finished in Thompson's Water Seal . 

Pergola

​May 2013 -Bagdad, FL

12 ft x 12 ft custom pergola - Constructed from treated pine lumber. 12 feet ceiling height provides a very grand feel. Client plans to install a paver base and has requested custom post skirting. Design incorporates the following unique features:

Custom end profiles
Built in lights on dimmer switch with hidden wiring
Wiring and switch installed for ceiling fan
Lap joint construction
Sealed end grain on corner posts to extend life

Arbor and Gate

​June 2014 - Bagdad, FL

Arbor - Custom arbor designed to match client's existing pergola. Constructed of treated pine lumber.

Custom Gate - Client requested a custom gate that allowed for riding mower entry and attractive passage into backyard. Constructed from yellow pine and finished with Minwax stain and spar urethane varnish. Gate is 48 inches wide and features:

Mortise and Tenon construction
Large speakeasy
Self-closing hinges and latch
Lockable 
Picture
© COPYRIGHT 2015. ALL RIGHTS RESERVED.
  • Home
  • INFO
    • Process
    • Ordering
    • Contact Us
  • Commissioned
  • Available Now
  • Blog